• Use the rear turnbuckle to adjust the furrow width of the leading body.
• Use the front turnbuckle to adjust the pulling point.
• The two functions do not influence each other.
• A few simple adjustments and the plough is set correctly the first time.
• No compensation or re-adjustment needed.
• The wide, infinitely-variable range ensures a rapid match to all tractors and operating conditions.

Optimum pulling point adjustment guarantees low landside pressure, resulting in less wear and low fuel consumption.

• Dual depth wheel – steel
• Dual depth wheel – pneumatic tyre
• Dual depth wheel – pneumatic tyre, hydraulically adjustable

Infinitely-variable hydraulic depth adjustment – one double-acting connection required.

• Pivot depth wheel – steel, without damping
• Pivot depth wheel – pneumatic tyre, without damping
• Pivot depth wheel – pneumatic tyre, hydraulic damping, can be used as transport wheel, located at last body

• Rear-mounted transport pivot wheel
• Forward-mounted transport pivot wheel – ideal for fenceline ploughing on 5-furrow ploughs upwards

The self-aligning wheel is hydraulically damped and swings backwards smoothly. The wheel can be converted into the transport wheel with a few simple adjustments.

• Forward-mounted transport pivot wheel, hydraulically adjustable
• Infinitely-variable hydraulic depth adjustment – one double-acting connection required.

• Optimum tractor efficiency and ploughing results at all times.
• All additional adjustments adapt to it correctly and automatically.
• Optimum adaptation to tractor power, slopes and field shapes.
• Easy ploughing of tight corners and headlands.
• Optimum fence-line ploughing from three-furrow models and above.

Durable construction

Important pivot points have wear-resistant, replaceable spring steel bushes for the highest pressure demands, and the pivot points can be lubricated.

NEW: SERVO 45 M PLUS

Up to 5 furrows, up to 240 hp.

Furrow width adjustment without lower linkage side to side movement.

• The fine adjustment system makes it possible to set-up once 100% to different tractor lower linkage dimensions, even if they deviate greatly from the norm.
• When you set the furrow width, there is then no need to adjust the front furrow width and pull line. The lower linkages remain parallel with no crabbing, essential for a straight furrow. Consistent landside pressure at all furrow widths.
• Memory cylinder technology for two functions as option. Beam pivot system and furrow width – the plough is pivoted and rotated, then re-adjusted to the pre-selected furrow width.

SERVO PLUS adjustment system with lever control and pivot point located away from the plough beam

• Smooth adjustment thanks to long adjusting lever.
• Protects the parallel linkage and pivot points.
• Clearly visible furrow width indicator.

The SERVO PLUS system is designed to allow hydraulic furrow width adjustment during ploughing. The hydraulic cylinder has a check valve so that the hoses are not under pressure during ploughing.

This system has a very clever triggering pressure system: The leg does not trip until the set resistance has been reached. Then the pressure required to trigger the leg reduces as the leg rises. No digging or loosening of big rocks. This protects the whole plough.

• On re-penetrating the soil, the pressure increases to ensure reliable penetration in heavy, dry soil.
• Set the trigger point quickly and easily using the pressure gauge on the headstock.

SERVO PLUS NOVA

These talented performers with hydraulic furrow width adjustment and hydraulic trip leg system offer maximum reliability and flexibility.

• The central filling system is standard on all SERVO NOVA ploughs.
• Smooth, flexible triggering protects both plough and tractor.
• The gas accumulators are mounted on the inside of the plough legs for protection.
• Spring-mounted disc coulters roll over rocks without the risk of damage.

NEW: SERVO 45 M PLUS NOVA

Up to 5 furrows, up to 240 hp

• The press is collected by the press arm’s large jaw. It is hydraulically released before the plough is reversed.
• A five-position mounting means the press can be set for different working widths. A tension spring pivots the press arm into the set catching position after releasing.
• On SERVO PLUS ploughs, the catching position is maintained precisely even if the furrow width is changed.
• The press arm can be fixed within the tractor width for road transport.
• The entire press arm can be removed quickly and easily.

• Double acting reversing cylinder with check valve; hoses are not under pressure during ploughing.
• The full-length mounting axle can be adjusted to four positions and has an anti-twist lock. Correct positioning on the tractor and optimum clearance at all times.

• The Reversing unit and turnover shaft has a diameter of 100 mm on the SERVO 35 and 110 mm on the SERVO 35 S.
• The reversing unit made from tempered cast steel is not welded to the reversing axle. The hydraulic hoses pass through the hollow shaft preventing trapping of the hoses during reversing.
• The heavy-duty tapered roller bearings are reliably protected from dirt and locked with an adjustable castellated nut.
• Beam angle is adjusted using two turnbuckles.

• The tempered leg mounting brackets have a large clamping surface to resist high stress. The bracket surrounds the plough beam with a large contact area for optimum transfer of forces to the beam.

An offset allows adjustment of body angle for reliable penetration, even in extremely hard, dry soils.

The landsides can be used four times to ensure cost efficient use of the parts. Landside protector standard on last body.

All shares are manufactured from hardened boron steel. Increasing the hardened wear zone extends service life by up to 50%. The 11 mm thick shares have a total width of 150 mm. The forward taper aids good penetration and has the effect of being self-sharpening.

with powerful wear points. A large angle guarantees good penetration. Highly suitable for stony soils and shallow ploughing. Armoured share points are available as an option.

• Longer service life than 3-layer plate.
• Improved soil flow reduces sticking.
• Developed and manufactured by PÖTTINGER.
• DURASTAR 27 Wc, 46 Wc, 36 UWc and 39 UWc mould boards

Mouldboards

8 mm hardened fine grain steel – extremely resistant to wear.

27 Wc DURASTAR

27 Wc DURASTARLow drag resistance, well suited to working on slopes. Ideal for ploughing meadow and flat land with good furrow clearance. Suitable for higher forward speeds.

• Working width up to 45 cm
• Working depth up to 25 cm
• Furrow clearing up to 48 cm

41 W

41 WLong, curved mould board for heavy, sticky soil. Moderate working speed.

• Working width up to 45 cm
• Working depth up to 30 cm
• Furrow clearing up to 45 cm

46 Wc DURASTAR

46 Wc DURASTARGood crumbling effect and suitable for slopes, low drag resistance in loam and clay soils, also light soil types. A body for high working speeds without overlapping. Wide furrow clearance, low draft and excellent turning of the soil ridge are the hallmarks of this mouldboard.

• Working width up to 54 cm
• Working depth up to 35 cm
• Furrow clearing up to 53 cm

36 UWc DURASTAR

36 UWc DURASTARUniversal body with very good furrow clearance and excellent crumbling at normal working speed. Large quantities of harvest trash are ploughed in tidily. A low-drag body, suitable for most soils.

• Working width up to 50 cm
• Working depth up to 30 cm
• Furrow clearing up to 48 cm

39 UWc DURASTAR

39 UWc DURASTARLarge universal mouldboard with very good furrow clearance and excellent crumbling at normal working speed. Large quantities of harvest trash are ploughed in tidily. A low-drag body, suitable for most soils.

• Working width up to 54 cm
• Working depth up to 35 cm
• Furrow clearing up to 50 cm

35 WSS

35 WSSSlatted body with strong turning characteristics, specially suitable for peaty, medium-density and sticky soil. Especially wide furrow clearing and excellent crumbling.

• Working width up to 54 cm
• Working depth up to 35 cm
• Furrow clearing up to 53 cm

38 WWS

38 WWSLow-drag resistance body with curved slats for excellent crumbling effect in medium to heavy soils (loam, clay). Good furrow clearance – ideal for wide tyres.

• Working width up to 54 cm
• Working depth up to 30 cm
• Furrow clearing up to 50 cm

• Working width up to 54 cm
• Working depth up to 35 cm
• Furrow clearing up to 53 cm

Adjustable bracket

One bracket for Standard and PLUS ploughs. Depth is adjusted using toothed segments.

• Mounting moved forward so the disc coulter is in front of the skimmer. Plenty of space for large quantities of maize straw and organic matter.
• Mounting moved back so the disc coulter is close to the skimmer for light, free-flowing soil and shallow ploughing.

• 500 or 590 mm diameter with good self-cleaning characteristics.
• Star-shape indentations keep disc coulters rotating.
• Especially wide bearing spacing for highest durability.
• Scalloped disc coulters rotate well in high levels of organic matter.

Knife coulter

Knife coulterThe landside knife coulter is a cost effective alternative to the disc coulter – from 22 cm working depth.

V1 universal skimmer

V1 universal skimmer

• Suitable for all conditions including maize straw

V2 maize skimmer

V2 maize skimmer

• For large quantities of organic matter, catch crops and deep tillage.

V3 universal skimmer

V3 universal skimmer

• Suitable for shallow working depths.

V5 maize skimmer

V5 maize skimmer

• Large, high skimmer board suitable for working in high volume harvest residues and for very deep ploughing.

Trashboards

TrashboardAlternatives for shallow ploughing and stony soil.

Leg deflector

Leg deflectorLeg deflectors improve ploughing results in large quantities of organic matter while protecting the leg.